Concrete

Fence Post Concrete Calculator

Estimate concrete around fence posts by subtracting the actual embedded post volume, then compare volume-based bag counts.

Created and Written by: Designation: Founder

Technically reviewed by: Riya Kulkarni | BE Civil Engineer

Measure the concrete and post

1. Concrete envelope inside each hole

Enter only the height occupied by concrete. Exclude gravel bedding, soil backfill and unfilled space above the concrete; do not enter excavation depth unless it is all concrete. Constant straight vertical sides are assumed. Starting dimensions are arithmetic examples, not approved hole sizing.

2. Actual post displacement

Use actual outside dimensions, not nominal lumber labels. Post length within concrete may be shorter than fill height when concrete extends below the post. It must be positive and no greater than fill height. Displacement uses only this overlap. The section is treated as solid or closed to concrete entry; open hollow posts that fill with concrete need a separate takeoff.

Assumes a centered post; rectangular post axes align with rectangular hole axes. A rectangular post’s diagonal must fit in a round hole. Fit checks do not establish adequate concrete cover, frost depth, bearing, wind resistance or footing design. Follow the project details for size and embedment.

3. Allowance & finished bag yield

Use the actual complete premix’s finished yield, not cement-only bag weight or loose dry volume. Starting 0.60 ft³ per bag and 10% allowance are editable examples. The yield selector retains its number; length selectors convert valid dimensions.

Pooled bags round the combined required volume once. Per-hole bags round each identical hole separately, which can increase the total. These are volume comparisons, not mixing or installation instructions. Confirm the product and its permitted handling; do not assume all post-setting mixes share one yield or method.

EXAMPLE ESTIMATE
0.375 yd³

10.128 ft³ / 0.287 m³ including allowance

Gross envelope per hole
1.091 ft³
Post displacement per hole
0.17 ft³
Net concrete per hole
0.921 ft³
Identical holes
10
Base total concrete
9.207 ft³
10% ordering allowance
0.921 ft³
Required per hole with allowance
1.013 ft³
Finished bag yield
0.6 ft³
Pooled volume bags
17
Whole bags per hole
2
Separately rounded bag total
20
Pooled purchased coverage
10.2 ft³
Pooled bag surplus beyond allowance
0.072 ft³

Calculation basis

Concrete per hole = hole area × concrete fill height − actual post area × post length inside concrete. Multiply by 10, then (1 + 10/100). Round required volume ÷ finished bag yield upward.

Decimal arithmetic preserves rectangular exact multiples; round sections use π approximated to 40 decimal places. Areas and volumes display to 3 decimals. Physical dimensions and product yields remain estimates. No tapered/belled holes, collars beyond fill height or footing design are inferred.

Formula and worked example

Gross concrete envelope per hole = hole cross-sectional area × concrete fill height. Post displacement = actual post cross-sectional area × post length within concrete. Net concrete per hole = gross envelope − post displacement. Multiply by identical hole count, then apply the chosen ordering allowance once.

For round sections, area = π × diameter² ÷ 4. For rectangular sections, area = width × length or thickness. All dimensions are converted to matching units before calculation.

Illustrative example: a 10 in diameter hole with 24 in concrete fill height encloses approximately 1.0908307825 ft³. A 3.5 in × 3.5 in actual rectangular post overlapping all 24 in displaces 0.1701388889 ft³. Net concrete is about 0.9206918936 ft³ per hole. Ten identical holes with an editable 10% allowance require 10.1276108297 ft³, or 0.3750966974 yd³.

At the editable example yield of 0.60 ft³ per bag, pooled volume needs 17 whole bags. Each hole separately needs 2 whole bags, giving 20 bags if all ten holes are rounded independently. Pooled purchased coverage is 10.2 ft³, with approximately 0.0723891703 ft³ beyond the allowance-adjusted requirement. These dimensions are arithmetic examples, not approved footing details.

Concrete fill height is not excavation depth

Enter the height of concrete only. Gravel bedding, soil backfill and unfilled space above the concrete do not count as concrete. If a hole has those layers, subtract them when determining the concrete fill height before entering it. Do not deduct the same layer twice.

The post length within concrete is the actual overlap between the post and that concrete envelope. It can be less than fill height if there is a concrete pad below the post. It cannot exceed the fill height. Concrete collars or caps outside the entered straight envelope need a separate volume takeoff.

Actual post size and fit

Use actual outside post dimensions, not nominal lumber names. The post is assumed centered. For a rectangular post in a round hole, its full diagonal must be smaller than hole diameter, not merely its width. In rectangular holes, post width and thickness align with the corresponding hole axes. A round post must fit within both rectangular axes.

The post section is treated as solid or as an enclosed void into which concrete cannot enter. An open hollow post that fills internally with concrete needs a separate displacement calculation. Tapered, belled, irregular or angled sections also need a different takeoff.

Fit validation only checks the entered geometry. It does not establish concrete cover, required embedment, frost depth, bearing, wind resistance or structural adequacy. Obtain hole and post details from the project design before estimating quantities.

Exact rectangular and metric references

A 12 in × 12 in rectangular hole with 24 in fill height has 2 ft³ gross envelope. A 6 in × 6 in post overlapping 24 in displaces 0.5 ft³, leaving 1.5 ft³ per hole. Four holes with zero allowance need exactly 6 ft³. At 0.60 ft³ per bag, pooled volume needs exactly 10 bags; independently rounding each hole gives 3 per hole and 12 bags total.

Metric arithmetic example: a 0.30 m × 0.30 m rectangular hole with 0.60 m fill height encloses 0.054 m³. A 0.10 m × 0.10 m post overlapping 0.50 m displaces 0.005 m³. Net is 0.049 m³ each. Two holes with zero allowance need 0.098 m³ or 98 L. At a user-entered 20 L per bag, pooled volume needs 5 bags; separately rounded holes need 3 each, or 6 total.

Bag rounding, allowance and product yield

Ordering allowance applies to unrounded net concrete volume before bag rounding. Pooled volume bags = round up(combined required volume ÷ finished yield per bag). Separately rounded bags = hole count × round up(required volume per hole ÷ finished yield per bag). The latter may be larger because each hole is rounded independently.

These are volume-based comparisons. They do not prescribe mixing, partial-bag handling or a post-setting installation method. Confirm the actual product’s finished yield and instructions. Cement-only bag weight and loose dry volume are not finished concrete yield. Different complete premixes and fast-setting post products can have different yields and methods.

Units, precision and limits

Dimensions accept feet, inches, yards, meters, centimeters and millimeters. Length selectors convert valid measurements. Bag yield accepts ft³, m³ or liters; its selector retains the numeric entry to match the source label. One cubic foot equals 0.028316846592 m³ and one cubic yard equals 27 ft³.

Rectangular geometry and decimal bag divisions use exact reduced fractions. Round geometry uses π approximated to 40 decimal places; measured geometry and labeled yields remain approximate. Whole-bag counts use the calculation values before display rounding to three decimals. Positive dimensions support 0.000001–1,000,000 ft after conversion. Hole count is an integer from 1 to 100,000; allowance accepts 0–100%. Total and allowance-adjusted concrete are limited to 1 billion ft³. Bag yield supports 0.000000001–1 m³ and estimates above 10 million bags are rejected as entry checks.

References

QUIKRETE Concrete Mix No. 1101 data sheet lists approximate finished yields, including 0.60 ft³ for its 80 lb bag. That yield is the form’s editable example; confirm the package being purchased.

QUIKRETE Setting Posts without Mixing distinguishes gravel bedding from concrete in a product-specific post-setting method. Civilable uses entered concrete fill height and does not import that method’s sizing or installation instructions into this quantity estimate.

Related calculators

All calculators

TECHNICAL REVIEWER

Riya Kulkarni | BE Civil Engineer

Riya Kulkarni qualifications and experience
QualificationBE Civil – Shivaji University, Kolhapur (2018)
Experience8+ Years
Technical SpecialisationsStructural Engineering, Construction Materials, Site Execution and Concrete Technology.

Project experience

1. Shree Ganesh Residency

Location: Rajarampuri, Kolhapur

Project Type: G+4 Residential Apartment Building

Technical responsibilities
  • RCC structural construction coordination.
  • Reinforcement and shuttering inspection.
  • Concrete pouring and curing supervision.
  • Monitoring construction materials and workmanship.
  • Site quality-control documentation.

2. Vrindavan Heights

Location: Tarabai Park, Kolhapur

Project Type: G+5 Residential Building

Technical responsibilities
  • Structural drawing interpretation.
  • Reinforcement detailing checks.
  • Concrete workability and placement monitoring.
  • Construction sequencing and site coordination.
  • Building material quality assessment.

3. Sai Krupa Row Houses

Location: Kalamba Road, Kolhapur

Project Type: Residential Row Housing Development

Technical responsibilities
  • Foundation and plinth construction coordination.
  • Brick masonry and plastering inspection.
  • Concrete mixing, placement and curing.
  • Waterproofing and finishing work coordination.
  • Construction progress documentation.

4. Greenview Enclave

Location: Ujalaiwadi, Kolhapur

Project Type: G+3 Residential Apartment Complex

Technical responsibilities
  • Site execution monitoring.
  • RCC work and reinforcement inspection.
  • Construction material management.
  • Concrete quality testing coordination.
  • Workmanship and quality documentation.

5. Lotus Business Plaza

Location: Shahupuri, Kolhapur

Project Type: G+3 Commercial Building

Technical responsibilities
  • Structural construction coordination.
  • Slab and column reinforcement inspection.
  • Concrete placement and quality monitoring.
  • Construction activity sequencing.
  • Contractor and site-team coordination.

6. Omkar Residency

Location: Kadamwadi, Kolhapur

Project Type: G+5 Residential Apartment Building

Technical responsibilities
  • Foundation and superstructure execution coordination.
  • Reinforcement and formwork inspection.
  • Concrete testing and curing monitoring.
  • Material specifications and quality checks.
  • Site inspection reporting.

7. Silver Oak Villas

Location: Kasaba Bawada, Kolhapur

Project Type: Independent Residential Villa Development

Technical responsibilities
  • Residential foundation construction.
  • RCC structural component inspection.
  • Masonry and plastering quality checks.
  • Flooring and finishing coordination.
  • Site execution and material monitoring.

8. Pratham Commercial Complex

Location: Ruikar Colony, Kolhapur

Project Type: Commercial and Retail Building

Technical responsibilities
  • RCC construction coordination.
  • Concrete quality-control procedures.
  • Structural component inspection.
  • Construction material assessment.
  • Execution progress and quality reporting.