Straight decking rows
This tool estimates decking surface boards for a net rectangular field. Choose the dimension parallel to the boards as the row run R; the other dimension W lies across rows. For actual board face width b and internal side gap g, the minimum row count N = ceil((W + g)/(b + g)), because N full-width boards and N − 1 internal gaps span Nb + (N − 1)g. No outer edge gap or perimeter border is added.
The model balances width trimming across the first and last rows. For N at least 2, each edge-row width = [W − (N − 2)b − (N − 1)g]/2, with N − 2 full-width interior rows. For one row, its trimmed width is W. This avoids treating a narrow leftover gap as a negative-width last board. It does not determine whether the resulting edge rips meet a product’s minimum width or fastening requirements.
Default US example
For a 12 ft row run and 10 ft across rows, with actual face width 5.5 in and side gap 0.25 in: N = ceil((120 + 0.25)/(5.5 + 0.25)) = 21 rows. Nineteen interior boards remain 5.5 in wide; two edge boards are 5.25 in each. Their combined face widths plus twenty 0.25 in gaps fill exactly 120 in. With zero end trim, each blank is 12 ft long. Ten percent extra blanks rounds ceil(21 × 1.10) to 24 blanks. A 16 ft usable stock board yields one blank, so purchase 24 stock boards, totaling 384 linear ft.
Repeated cuts from one stock length
With extra trim t at each row end, cut blank C = R + 2t. Let usable stock length be S and separating saw kerf k. A stock board can provide floor((S + k)/(C + k)) identical blanks, corresponding to qC + (q − 1)k ≤ S. Stock purchases = ceil(total blanks / blanks per stock). Factory-end preparation must already be deducted from usable S. Side-rip scraps are not reused for another row, and no mixed-length cutting optimization is attempted.
For a 4 ft × 4 ft field, the same width and gap give 9 rows. With zero spare allowance and 48 in blanks, a 96 in stock board cannot provide two blanks when kerf is 0.125 in; two blanks require 96.125 in. At exactly 96.125 in usable stock, two blanks fit and ceil(9/2) gives 5 stock boards. This is an identical-cut capacity model, not a complete saw sequence, defect allowance or fabrication plan. Stock shorter than one full blank is rejected; the tool does not invent unsupported butt joints.
Metric example
A 4 m row run and 3 m field width with 140 mm boards and 5 mm internal gaps gives 21 rows, including two 120 mm edge boards. Extra trim of 50 mm at each end makes each blank 4.1 m. A 4.2 m usable stock length gives one blank per stock; 10% extra blanks produces 24 stock boards, totaling 100.8 m. All dimensions are illustrative, not a recommended product, gap or layout.
Scope and input limits
Enter net field dimensions after perimeter clearances and border-board areas. Use actual board width, not nominal lumber size. Side gaps depend on product, fasteners and installation conditions. The calculator does not select a gap, assess minimum rip widths, design structural spans or calculate joists, beams, posts, footings, railings, stairs, fascia or fasteners. Diagonal patterns, butt joints, borders and mixed stock lengths need separate takeoffs.
Positive lengths are 0.000001–1,000,000 ft after conversion. Gap and kerf are 0–1 ft, gap must be less than board face width, and end trim is 0–100 ft per end. Field area is capped at 1,000,000 m², rows and allowance-adjusted blanks at 1 million, and purchased stock at 1 billion linear ft. Spare percentage is 0–100 with four decimal places. These are software limits, not allowable design values. Decimal fractions determine row/cut/order boundaries exactly before three-decimal display rounding.
Primary references
Trex board-spacing guidance discusses spacing factors and checking product installation requirements. TimberTech board-spacing guidance distinguishes side-to-side and end-to-end spacing and product/fastener dependencies. Sources checked 4 November 2026. The row, balanced-rip and repeated-cut equations here are original geometry; no manufacturer endorsement, product compatibility or structural approval is claimed.
Related tools
Use the Square Footage Calculator to measure separate rectangular fields. For a separate hardscape surface rather than decking, see the Paver Patio Calculator. Keep each surface, material and installation plan distinct.